 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
(Partial) List of International Standards
SAE
SAE J343 Test and Test Procedures for SAE 100R Series
Hydraulic Hose and Hose Assemblies. Impulse, Burst, Hidrostatic
and other hydraulic teste
Publisher: SAE International Publication Date: Jan 1, 2004
This SAE Standard gives methods for testing and evaluating
performance of the SAE 100R series of hydraulic hose and hose
assemblies (hose and attached end fittings) used in hydraulic fluid
power systems.
SAE J1405 OPTIONAL Test Procedures for Hydraulic Hose
Assemblies. mpulse, Burst, Hidrostatic and other hydraulic teste
Publisher: SAE International Publication Date: Nov 1, 2005
The procedures contained in this SAE Recommended Practice
have been developed to establish uniform methods for impulse
and high temperature circulation testing of hydraulic hose
assemblies under special conditions not specified in SAE J343 for
SAE J517 hoses. Basic test procedures are to be in accordance
with SAE J343 except as modified in this document.
SAE AIR 4298 Impulse Test Machine, Sine Wave, Equipment and
Operation
Publisher: SAE International Publication Date: Jan 27, 1992
SAE ARP603G Impulse Testing of Hydraulic Hose, Tubing, and
Fitting Assemblies (Cancelled in June 2008)
SAE MA2002A Impulse Testing of Hydraulic Hose, Tubing and
Fitting Assemblies
Publisher: SAE International Publication Date: Jul 1, 1988
Arp1383 This SAE ARP establishes minimum requirements for
impulse testing of aerospace hydraulic actuators, valves, pressure
containers, and similar fluid system components, except
accumulators, for use in aerospace hydraulic systems.
ARP1383C REV.: 2013-04-22
This SAE Aerospace Recommended Practice (ARP) defines
impulse test procedures that are recommended for hydraulic
components. ARP1383 has been updated to Revision C for the
following reasons: a. Technical changes have been made including
adding a section on scatter factors and an appendix that is
associated with this topic, and deleting the original Appendix A.
b. The references in the document have been updated. c.
Editorial changes have been made to improve the readability of
the document.
AS603 SAE Aerospace Standard (AS) establishes impulse testing
of hose, tubing, and fitting assemblies for use in aerospace
hydraulic systems.
SAE J1985 - Fuel Filter - Initial Single-Pass Efficiency Test Method
AS604, AS614, AS620 / AS1227, AS1339, AS1424, AS1946,
AS1975, AS2078, AS5951
ISO
ISO 6772 Aerospace - Fluid Systems - Impulse Testing of
Hydraulic Hose, Tubing and Fitting Assemblies Second Edition
Publisher: International Organization for Standardization
Publication Date: Jan 1, 1988
ISO 8032 Rubber and Plastics Hose Assemblies - Flexing
Combined with Hydraulic Impulse Test (Half-Omega Test)
Publisher: International Organization for Standardization
Publication Date: Jul 15, 1997
ISO 6802 Rubber and plastics hoses and hose assemblies with
wire reinforcements Hydraulic impulse test with flexing
Publisher: International Organization for Standardization
Publication Date: Oct 1, 2005
ISO 6803 Rubber or Plastics Hoses and Hose Assemblies -
Hydraulic-Pressure Impulse Test without Flexing Second Edition
Publisher: International Organization for Standardization
Publication Date: Aug 15, 2008
This International Standard describes hose impulse testing,
without flexing, of rubber or plastics hydraulic hose assemblies at
both high and low impulse pressures.
CEN EN ISO 6803 Rubber or plastics hoses and hose
assemblies - Hydraulic pressure impulse test without flexing
Publisher: European Committee for Standardization Publication
Date: Aug 1, 2008
ISO 4548-4 Methods of test for full-flow lubricating oil filters for
internal combustion engines Part 4: Initial particle retention
efficiency, life and cumulative efficiency (gravimetric method)
Internal-combustion-engines ISO 4548-4:1997 Identical to BS
7403-4:1998
ISO7241-2 testing of Hydraulic Quick releasing couplings
ISO 8829
MIL & Others
NAVY MIL-V-24695A VALVE, HOSE ASSEMBLY, AND ADAPTER,
VENT AND TEST HYDRAULIC SERVICE, GENERAL
SPECIFICATION FOR (METRIC)
Publisher: Naval Sea Systems Command (Ship Systems)
Publication Date: Dec 23, 1991
This specification covers vent and test valves, hose assemblies
and adapters suitable for hydraulic service to a maximum
operating pressure of 310 bar (4,500 pounds per square inch
(lb/in2)).
MIL-DTL-25579
ASTM D 380 Standard Test Methods for Rubber Hose
Publisher: ASTM International Publication Date: Nov 15, 1994
These test methods cover procedures for inspection and test of all
types and constructions of rubber hose.
Are designed for worst-case transient condition on light vehicles
engines as well as heavy-duty engines.
UL1405
For Airleess Paint Hoses and other applications
CSA
ANSI/CSA NGV 4.2 of 2014
CSA12.52-M99 NFPA 52 & ECE R110
ABS
ABS2238, ABS1335, ABS2149
AUTOMOTIVE
Ford, GMW, GM, PSA, Fiat, Chrysler, BMW, AUDI, Mercedes, VW,
Renault,
TEST FLUIDS
MIL & Others
Aerospace - Chlorinated Solvent Contamination of Mil-H-5606/Mil-H-
83282 Vehicle Hydraulic Systems
Document Number: AIR4713 Date Reaffirmed: August 2002
Issuing Committee: SAE A-6c3 Fluids Committee
Aircraft hydraulic fluids fall under various specifications:
Common petroleum-based:
Mil-H-5606: Mineral base, flammable, fairly low flashpoint, usable
from -65 °F (-54 °C) to 275 °F (135 °C), red color
Mil-H-83282: Synthetic hydrocarbon base, higher flashpoint, self-
extinguishing, backward compatible to -5606, red color
Mil-H-87257: A development of -83282 fluid to improve its low
temperature viscosity.
Phosphate-ester based:
BMS 3-11: Skydrol 500B-4, Skydrol LD-4, Skydrol 5 and Exxon
HyJetIV-A plus – Typically light purple, not compatible with
petroleum-based fluids, will not support combustion.
MIL-H-5606 MIL-PRF-7808 MIL-prf-87257
MIL-H-87257 MIL-H-83282 MIL-prf-
SKYDROL Water Water-glycol
Glycol
JP1 (Fuel) JP8 (Fuel) MIL-F-7024
Compressed air Nitrogen Steam
Diathermyc oil
SAE
SAE J343 Test and Test Procedures for SAE 100R Series
Hydraulic Hose and Hose Assemblies. Impulse, Burst, Hidrostatic
and other hydraulic teste
Publisher: SAE International Publication Date: Jan 1, 2004
This SAE Standard gives methods for testing and evaluating
performance of the SAE 100R series of hydraulic hose and hose
assemblies (hose and attached end fittings) used in hydraulic fluid
power systems.
SAE J1405 OPTIONAL Test Procedures for Hydraulic Hose
Assemblies. mpulse, Burst, Hidrostatic and other hydraulic teste
Publisher: SAE International Publication Date: Nov 1, 2005
The procedures contained in this SAE Recommended Practice
have been developed to establish uniform methods for impulse
and high temperature circulation testing of hydraulic hose
assemblies under special conditions not specified in SAE J343 for
SAE J517 hoses. Basic test procedures are to be in accordance
with SAE J343 except as modified in this document.
SAE AIR 4298 Impulse Test Machine, Sine Wave, Equipment and
Operation
Publisher: SAE International Publication Date: Jan 27, 1992
SAE ARP603G Impulse Testing of Hydraulic Hose, Tubing, and
Fitting Assemblies (Cancelled in June 2008)
SAE MA2002A Impulse Testing of Hydraulic Hose, Tubing and
Fitting Assemblies
Publisher: SAE International Publication Date: Jul 1, 1988
Arp1383 This SAE ARP establishes minimum requirements for
impulse testing of aerospace hydraulic actuators, valves, pressure
containers, and similar fluid system components, except
accumulators, for use in aerospace hydraulic systems.
ARP1383C REV.: 2013-04-22
This SAE Aerospace Recommended Practice (ARP) defines
impulse test procedures that are recommended for hydraulic
components. ARP1383 has been updated to Revision C for the
following reasons: a. Technical changes have been made including
adding a section on scatter factors and an appendix that is
associated with this topic, and deleting the original Appendix A.
b. The references in the document have been updated. c.
Editorial changes have been made to improve the readability of
the document.
AS603 SAE Aerospace Standard (AS) establishes impulse testing
of hose, tubing, and fitting assemblies for use in aerospace
hydraulic systems.
SAE J1985 - Fuel Filter - Initial Single-Pass Efficiency Test Method
AS604, AS614, AS620 / AS1227, AS1339, AS1424, AS1946,
AS1975, AS2078, AS5951
ISO
ISO 6772 Aerospace - Fluid Systems - Impulse Testing of
Hydraulic Hose, Tubing and Fitting Assemblies Second Edition
Publisher: International Organization for Standardization
Publication Date: Jan 1, 1988
ISO 8032 Rubber and Plastics Hose Assemblies - Flexing
Combined with Hydraulic Impulse Test (Half-Omega Test)
Publisher: International Organization for Standardization
Publication Date: Jul 15, 1997
ISO 6802 Rubber and plastics hoses and hose assemblies with
wire reinforcements Hydraulic impulse test with flexing
Publisher: International Organization for Standardization
Publication Date: Oct 1, 2005
ISO 6803 Rubber or Plastics Hoses and Hose Assemblies -
Hydraulic-Pressure Impulse Test without Flexing Second Edition
Publisher: International Organization for Standardization
Publication Date: Aug 15, 2008
This International Standard describes hose impulse testing,
without flexing, of rubber or plastics hydraulic hose assemblies at
both high and low impulse pressures.
CEN EN ISO 6803 Rubber or plastics hoses and hose
assemblies - Hydraulic pressure impulse test without flexing
Publisher: European Committee for Standardization Publication
Date: Aug 1, 2008
ISO 4548-4 Methods of test for full-flow lubricating oil filters for
internal combustion engines Part 4: Initial particle retention
efficiency, life and cumulative efficiency (gravimetric method)
Internal-combustion-engines ISO 4548-4:1997 Identical to BS
7403-4:1998
ISO7241-2 testing of Hydraulic Quick releasing couplings
ISO 8829
MIL & Others
NAVY MIL-V-24695A VALVE, HOSE ASSEMBLY, AND ADAPTER,
VENT AND TEST HYDRAULIC SERVICE, GENERAL
SPECIFICATION FOR (METRIC)
Publisher: Naval Sea Systems Command (Ship Systems)
Publication Date: Dec 23, 1991
This specification covers vent and test valves, hose assemblies
and adapters suitable for hydraulic service to a maximum
operating pressure of 310 bar (4,500 pounds per square inch
(lb/in2)).
MIL-DTL-25579
ASTM D 380 Standard Test Methods for Rubber Hose
Publisher: ASTM International Publication Date: Nov 15, 1994
These test methods cover procedures for inspection and test of all
types and constructions of rubber hose.
Are designed for worst-case transient condition on light vehicles
engines as well as heavy-duty engines.
UL1405
For Airleess Paint Hoses and other applications
CSA
ANSI/CSA NGV 4.2 of 2014
CSA12.52-M99 NFPA 52 & ECE R110
ABS
ABS2238, ABS1335, ABS2149
AUTOMOTIVE
Ford, GMW, GM, PSA, Fiat, Chrysler, BMW, AUDI, Mercedes, VW,
Renault,
TEST FLUIDS
MIL & Others
Aerospace - Chlorinated Solvent Contamination of Mil-H-5606/Mil-H-
83282 Vehicle Hydraulic Systems
Document Number: AIR4713 Date Reaffirmed: August 2002
Issuing Committee: SAE A-6c3 Fluids Committee
Aircraft hydraulic fluids fall under various specifications:
Common petroleum-based:
Mil-H-5606: Mineral base, flammable, fairly low flashpoint, usable
from -65 °F (-54 °C) to 275 °F (135 °C), red color
Mil-H-83282: Synthetic hydrocarbon base, higher flashpoint, self-
extinguishing, backward compatible to -5606, red color
Mil-H-87257: A development of -83282 fluid to improve its low
temperature viscosity.
Phosphate-ester based:
BMS 3-11: Skydrol 500B-4, Skydrol LD-4, Skydrol 5 and Exxon
HyJetIV-A plus – Typically light purple, not compatible with
petroleum-based fluids, will not support combustion.
MIL-H-5606 MIL-PRF-7808 MIL-prf-87257
MIL-H-87257 MIL-H-83282 MIL-prf-
SKYDROL Water Water-glycol
Glycol
JP1 (Fuel) JP8 (Fuel) MIL-F-7024
Compressed air Nitrogen Steam
Diathermyc oil
______________________________________
Haidar, Inc. ______________________________________________________
_______________________________________________________________________________________________
Haidar, Inc. ______________________________________________________
_______________________________________________________________________________________________